# TI Jacinto6+ Board not booting after mender converted image added to SD card; U-boot errors

**URL:** <https://hub.mender.io/t/ti-jacinto6-board-not-booting-after-mender-converted-image-added-to-sd-card-u-boot-errors/5191>\
**Category:** Board Integrations\
**Tags:** u-boot, uboot\
**Created:** [August 12, 2022, 12:38pm UTC](https://hub.mender.io/t/ti-jacinto6-board-not-booting-after-mender-converted-image-added-to-sd-card-u-boot-errors/5191 "2022-08-12T12:38:23Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![Nalin](https://avatars.discourse-cdn.com/v4/letter/n/ecd19e/32.png) [@Nalin](https://hub.mender.io/u/Nalin)\
**Post date:** [August 12, 2022, 12:38pm UTC](https://hub.mender.io/t/ti-jacinto6-board-not-booting-after-mender-converted-image-added-to-sd-card-u-boot-errors/5191/1 "2022-08-12T12:38:23Z")

</div>

Hi

I have created a 4 partition image as suggested in the mender documents for the TI Jacinto 6+ board using mender-convert and have added the same to the SD card which is used by the board to boot. While booting I get the following error:

Hit any key to stop autoboot: 0  
=\> setenv mmcdev 0  
=\> saveenv  
Saving Environment to MMC…  
Writing to MMC(1)… done  
=\> boot  
switch to partitions #0, OK  
mmc0 is current device  
SD/MMC found on device 0  
reading boot.scr  
\*\* Unable to read file boot.scr \*\*  
reading uEnv.txt  
290 bytes read in 3 ms (93.8 KiB/s)  
Loaded env from uEnv.txt  
Importing environment from mmc0 …  
switch to partitions #0, OK  
mmc0 is current device  
SD/MMC found on device 0  
\*\* File not found /boot/zImage \*\*  
\*\* First descriptor is NOT a primary desc on 1:1 \*\*  
switch to partitions #0, OK  
mmc1(part 0) is current device  
\*\* First descriptor is NOT a primary desc on 1:1 \*\*  
mmc - MMC sub system

Usage:  
mmc info - display info of the current MMC device  
mmc read addr blk# cnt  
mmc write addr blk# cnt  
mmc erase blk# cnt  
mmc rescan  
mmc part - lists available partition on current mmc device  
mmc dev [dev] [part] - show or set current mmc device [partition]  
mmc list - lists available devices  
mmc hwpartition [args…] - does hardware partitioning  
arguments (sizes in 512-byte blocks):  
[user [enh start cnt] [wrrel {on|off}]] - sets user data area attributes  
[gp1|gp2|gp3|gp4 cnt [enh] [wrrel {on|off}]] - general purpose partition  
[check|set|complete] - mode, complete set partitioning completed  
WARNING: Partitioning is a write-once setting once it is set to complete.  
Power cycling is required to initialize partitions after set to complete.  
mmc bootbus dev boot\_bus\_width reset\_boot\_bus\_width boot\_mode

- Set the BOOT\_BUS\_WIDTH field of the specified device  
mmc bootpart-resize 
- Change sizes of boot and RPMB partitions of specified device  
mmc partconf dev boot\_ack boot\_partition partition\_access
- Change the bits of the PARTITION\_CONFIG field of the specified device  
mmc rst-function dev value
- Change the RST\_n\_FUNCTION field of the specified device  
WARNING: This is a write-once field and 0 / 1 / 2 are the only valid values.  
mmc setdsr - set DSR register value

mmc - MMC sub system

Usage:  
mmc info - display info of the current MMC device  
mmc read addr blk# cnt  
mmc write addr blk# cnt  
mmc erase blk# cnt  
mmc rescan  
mmc part - lists available partition on current mmc device  
mmc dev [dev] [part] - show or set current mmc device [partition]  
mmc list - lists available devices  
mmc hwpartition [args…] - does hardware partitioning  
arguments (sizes in 512-byte blocks):  
[user [enh start cnt] [wrrel {on|off}]] - sets user data area attributes  
[gp1|gp2|gp3|gp4 cnt [enh] [wrrel {on|off}]] - general purpose partition  
[check|set|complete] - mode, complete set partitioning completed  
WARNING: Partitioning is a write-once setting once it is set to complete.  
Power cycling is required to initialize partitions after set to complete.  
mmc bootbus dev boot\_bus\_width reset\_boot\_bus\_width boot\_mode

- Set the BOOT\_BUS\_WIDTH field of the specified device  
mmc bootpart-resize 
- Change sizes of boot and RPMB partitions of specified device  
mmc partconf dev boot\_ack boot\_partition partition\_access
- Change the bits of the PARTITION\_CONFIG field of the specified device  
mmc rst-function dev value
- Change the RST\_n\_FUNCTION field of the specified device  
WARNING: This is a write-once field and 0 / 1 / 2 are the only valid values.  
mmc setdsr - set DSR register value

Booting from eMMC …  
Wrong Image Format for bootm command  
ERROR: can’t get kernel image!

Any help would be appreciated in resolving this issue

---

<div class="post-metadata">

**Author:** ![TheYoctoJester](https://yyz2.discourse-cdn.com/flex036/user_avatar/hub.mender.io/theyoctojester/32/1444_2.png) [@TheYoctoJester](https://hub.mender.io/u/TheYoctoJester)\
**Post date:** [August 12, 2022, 1:28pm UTC](https://hub.mender.io/t/ti-jacinto6-board-not-booting-after-mender-converted-image-added-to-sd-card-u-boot-errors/5191/2 "2022-08-12T13:28:51Z")

</div>

Hi @Nalin,

Which configuration did you start off? It might need some fine tuning for your specific board.

Greetz,  
Josef

---

<div class="post-metadata">

**Author:** ![Nalin](https://avatars.discourse-cdn.com/v4/letter/n/ecd19e/32.png) [@Nalin](https://hub.mender.io/u/Nalin)\
**Post date:** [August 16, 2022, 6:53am UTC](https://hub.mender.io/t/ti-jacinto6-board-not-booting-after-mender-converted-image-added-to-sd-card-u-boot-errors/5191/3 "2022-08-16T06:53:56Z")

</div>

Hi TheYoctoJester

I have used the Beaglebone Black configuration available on Mender Hub as a reference.  
Link: [Beaglebone Black Debian](https://hub.mender.io/t/beaglebone-black-debian/1542)

Thanks  
Nalin

---

<div class="post-metadata">

**Author:** ![TheYoctoJester](https://yyz2.discourse-cdn.com/flex036/user_avatar/hub.mender.io/theyoctojester/32/1444_2.png) [@TheYoctoJester](https://hub.mender.io/u/TheYoctoJester)\
**Post date:** [August 16, 2022, 6:57am UTC](https://hub.mender.io/t/ti-jacinto6-board-not-booting-after-mender-converted-image-added-to-sd-card-u-boot-errors/5191/4 "2022-08-16T06:57:59Z")

</div>

Hi @Nalin

That won’t work right out of the box unfortunately. I would suggest to look at the original boot proved to figure out the necessary modifications. Chances are that you’ll have to provide a patched boot loader binary.

Greets

---

<div class="post-metadata">

**Author:** ![Nalin](https://avatars.discourse-cdn.com/v4/letter/n/ecd19e/32.png) [@Nalin](https://hub.mender.io/u/Nalin)\
**Post date:** [August 16, 2022, 8:41am UTC](https://hub.mender.io/t/ti-jacinto6-board-not-booting-after-mender-converted-image-added-to-sd-card-u-boot-errors/5191/5 "2022-08-16T08:41:53Z")

</div>

Hi @TheYoctoJester

I have made changes in U-boot as per the mender documentation([Manual U-Boot integration | Mender documentation](https://docs.mender.io/system-updates-yocto-project/board-integration/bootloader-support/u-boot/manual-u-boot-integration))  
To be exact the changes I have made in u-boot are in the board specific files under include/configs :

1. defined `CONFIG_BOOTCOUNT_LIMIT`
2. defined `CONFIG_BOOTCOUNT_ENV` and turned off other CONFIG\_BOOTCOUNT\_ features
3. defined `CONFIG_ENV_IS_IN_MMC`
4. removed FAT\_ENV\_\*
5. Added added “run mender\_try\_to\_recover” to bootcmd alongwith “run mender\_setup” as the first command
6. Replaced ${bootpart} with ${mender\_uboot\_root} in loadimage
7. Ensured that kernel image is in the /boot directory  
I have compiled the u-boot source code with these changes and used the binary along with rootfs files to create a disk image which was given as an input to the mender-convert tool which generated the mender .img file which was written to the SD card with the four required partitions.  
On booting from this SD card, boot fails and the log says mender\_setup and mender\_try\_to\_recover not defined.  
(I am unable to attach the entire log as a text file or add it directly in this post due to the word count limit)

Edit: Adding printenv details

> EXPORT table = fef9de60, htab.size = 521, htab.filled = 84, size = 0  
> Unsorted: n=84  
> 0: fdf35698 ==\> emmc\_android\_boot =\> setenv eval\_bootargs setenv bootargs $bootargs; run eval\_bootargs; setenv mmcdev 1; setenv fdt\_part 3; setenv boot\_part 9; if test $reboot\_image = recovery;  
> 1: fdf35710 ==\> bootdir =\> /boot  
> 2: fdf35774 ==\> bootm\_size =\> 0x10000000  
> 3: fdf35878 ==\> boot\_fit =\> 0  
> 4: fdf35918 ==\> loadbootenv =\> fatload ${mender\_uboot\_boot} ${loadaddr} ${bootenvfile}  
> 5: fdf35940 ==\> ver =\> U-Boot 2016.05-dirty (Aug 02 2022 - 11:03:00 +0530)  
> 6: fdf359cc ==\> dofastboot =\> 0  
> 7: fdf35a6c ==\> netloadimage =\> tftp ${loadaddr} ${bootfile}  
> 8: fdf35b34 ==\> arch =\> arm  
> 9: fdf35c38 ==\> mmcdev =\> 1  
> 10: fdf35d64 ==\> fdtcontroladdr =\> fdefef18  
> 11: fdf35da0 ==\> serial# =\> 0b0120124c0c0020  
> 12: fdf35ddc ==\> machid =\> fe6  
> 13: fdf35df0 ==\> board\_name =\> dra76x  
> 14: fdf35e04 ==\> pxefile\_addr\_r =\> 0x80100000  
> 15: fdf35f6c ==\> importbootenv =\> echo Importing environment from ${mender\_uboot\_boot} …; env import -t ${loadaddr} ${filesize}  
> 16: fdf35f94 ==\> scriptaddr =\> 0x80000000  
> 17: fdf35fa8 ==\> envboot =\> mmc dev ${mender\_uboot\_dev}; if mmc rescan; then echo SD/MMC found on device ${mender\_uboot\_dev};if run loadbootscript; then run bootscript;else if run loadbooten;  
> 18: fdf35fbc ==\> fastboot.userdata\_size =\> unknown  
> 19: fdf36034 ==\> dfu\_alt\_info\_qspi =\> MLO raw 0x0 0x040000;u-boot.img raw 0x040000 0x0100000;u-boot-spl-os raw 0x140000 0x080000;u-boot-env raw 0x1C0000 0x010000;u-boot-env.backup raw 0x1D0000 0  
> 20: fdf360ac ==\> ethaddr =\> f8:36:9b:0c:5f:62  
> 21: fdf360e8 ==\> fastboot.board\_rev =\> A.2  
> 22: fdf360fc ==\> fdt\_addr\_r =\> 0x88000000  
> 23: fdf36138 ==\> boot\_part =\> 9  
> 24: fdf36174 ==\> dfu\_bufsiz =\> 0x10000  
> 25: fdf361b0 ==\> finduuid =\> part uuid ${mender\_uboot\_root} uuid  
> 26: fdf361d8 ==\> vendor =\> ti  
> 27: fdf36250 ==\> partitions\_android =\> uuid\_disk=${uuid\_gpt\_disk};name=xloader,start=128K,size=256K,uuid=${uuid\_gpt\_xloader};name=bootloader,size=2304K,uuid=${uuid\_gpt\_bootloader};name=environm}  
> 28: fdf36278 ==\> bootscript =\> echo Running bootscript from ${mender\_uboot\_boot} …; source ${loadaddr}  
> 29: fdf362a0 ==\> args\_mmc =\> run finduuid;setenv bootargs console=${console} ${optargs} root=PARTUUID=${uuid} rw rootfstype=${mmcrootfstype}  
> 30: fdf36318 ==\> baudrate =\> 115200  
> 31: fdf36430 ==\> usbtty =\> cdc\_acm  
> 32: fdf36494 ==\> args\_fit =\> setenv bootargs console=${console}  
> 33: fdf365e8 ==\> dfu\_alt\_info\_emmc =\> rawemmc raw 0 3751936;boot part 1 1;rootfs part 1 2;MLO fat 1 1;MLO.raw raw 0x100 0x100;u-boot.img.raw raw 0x300 0x1000;u-env.raw raw 0x1300 0x200;spl-os-a1  
> 34: fdf3673c ==\> bootcmd =\> run mender\_setup  
> 35: fdf367a0 ==\> kernel\_addr\_r =\> 0x82000000  
> 36: fdf36944 ==\> mmcrootfstype =\> ext4 rootwait  
> 37: fdf36a20 ==\> fit\_loadaddr =\> 0x88000000  
> 38: fdf36a34 ==\> fastboot.secure =\> GP  
> 39: fdf36a5c ==\> bootfile =\> zImage  
> 40: fdf36a84 ==\> netloadfdt =\> tftp ${fdtaddr} ${fdtfile}  
> 41: fdf36ae8 ==\> board =\> dra7xx  
> 42: fdf36b38 ==\> stderr =\> serial@4806a000  
> 43: fdf36b4c ==\> bootenvfile =\> uEnv.txt  
> 44: fdf36b74 ==\> vram =\> 16M  
> 45: fdf36c3c ==\> fdtfile =\> dra76-evm.dtb  
> 46: fdf36d68 ==\> netargs =\> setenv bootargs console=${console} ${optargs} root=/dev/nfs nfsroot=${serverip}:${rootpath},${nfsopts} rw ip=dhcp  
> 47: fdf36e1c ==\> loadaddr =\> 0x82000000  
> 48: fdf36f84 ==\> rdaddr =\> 0x88080000  
> 49: fdf36f98 ==\> bootdelay =\> 2  
> 50: fdf36fac ==\> dfu\_alt\_info\_mmc =\> boot part 0 1;rootfs part 0 2;MLO fat 0 1;MLO.raw raw 0x100 0x100;u-boot.img.raw raw 0x300 0x1000;u-env.raw raw 0x1300 0x200;spl-os-args.raw raw 0x1500 0x201  
> 51: fdf37074 ==\> rootpath =\> /export/rootfs  
> 52: fdf370c4 ==\> loadimage =\> load mmc ${mender\_uboot\_root} ${loadaddr} ${bootdir}/${bootfile}  
> 53: fdf3713c ==\> fdtaddr =\> 0x88000000  
> 54: fdf371c8 ==\> scsidevs =\> 0  
> 55: fdf371f0 ==\> nfsopts =\> nolock  
> 56: fdf37308 ==\> eval\_bootargs =\> setenv bootargs androidboot.serialno=${serial#}  
> 57: fdf3731c ==\> stdin =\> serial@4806a000  
> 58: fdf37330 ==\> cpu =\> armv7  
> 59: fdf37344 ==\> partitions =\> uuid\_disk=${uuid\_gpt\_disk};name=rootfs,start=2MiB,size=-,uuid=${uuid\_gpt\_rootfs}  
> 60: fdf373a8 ==\> stdout =\> serial@4806a000  
> 61: fdf373bc ==\> devtype =\> mmc  
> 62: fdf3745c ==\> loadfdt =\> load ${mender\_uboot\_root} ${fdtaddr} ${bootdir}/${fdtfile}  
> 63: fdf374ac ==\> fastboot.cpu =\> DRA762  
> 64: fdf374c0 ==\> ramdisk\_addr\_r =\> 0x88080000  
> 65: fdf37510 ==\> boot\_os =\> 0  
> 66: fdf3763c ==\> update\_to\_fit =\> setenv loadaddr ${fit\_loadaddr}; setenv bootfile ${fit\_bootfile}  
> 67: fdf376a0 ==\> board\_rev =\> A.2  
> 68: fdf378d0 ==\> loadfit =\> run args\_fit; bootm ${loadaddr}#${fdtfile};  
> 69: fdf37948 ==\> console =\> ttyO0,115200n8  
> 70: fdf37970 ==\> dfu\_alt\_info\_ram =\> kernel ram 0x80200000 0x4000000;fdt ram 0x80f80000 0x80000;ramdisk ram 0x81000000 0x4000000  
> 71: fdf37984 ==\> soc =\> omap5  
> 72: fdf37a10 ==\> mmcboot =\> if mmc dev ${mender\_uboot\_dev}; then setenv devnum ${mender\_uboot\_dev}; setenv devtype mmc; if mmc rescan; then echo SD/MMC found on device ${mender\_uboot\_dev};if;  
> 73: fdf37a88 ==\> static\_ip =\> ${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off  
> 74: fdf37aec ==\> fit\_bootfile =\> fitImage.itb  
> 75: fdf37b8c ==\> reboot\_image =\> boot  
> 76: fdf37c2c ==\> findfdt =\> if test $board\_name = omap5\_uevm; then setenv fdtfile omap5-uevm.dtb; fi; if test $board\_name = dra7xx; then setenv fdtfile dra7-evm.dtb; fi;if test $board\_name =3  
> 78: fdf37c7c ==\> loadbootscript =\> load ${mender\_uboot\_boot} ${loadaddr} boot.scr  
> 79: fdf37e0c ==\> mmcloados =\> run args\_mmc; if test ${boot\_fdt} = yes || test ${boot\_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdtaddr}; else if test ${boot\_fdt} = try; then ;  
> 80: fdf37e84 ==\> netboot =\> echo Booting from network …; setenv autoload no; dhcp; run netloadimage; run netloadfdt; run netargs; bootz ${loadaddr} - ${fdtaddr}  
> 81: fdf37eac ==\> bootargs =\> console=ttyO0,115200n8 root=PARTUUID= rw rootfstype=ext4 rootwait  
> 82: fdf37ee8 ==\> bootcount =\> 1  
> 83: fdf37f24 ==\> boot\_fdt =\> try  
> arch=arm  
> args\_fit=setenv bootargs console=${console}  
> args\_mmc=run finduuid;setenv bootargs console=${console} ${optargs} root=PARTUUID=${uuid} rw rootfstype=${mmcrootfstype}  
> baudrate=115200  
> board=dra7xx  
> board\_name=dra76x  
> board\_rev=A.2  
> boot\_fdt=try  
> boot\_fit=0  
> boot\_os=0  
> boot\_part=9  
> bootargs=console=ttyO0,115200n8 root=PARTUUID= rw rootfstype=ext4 rootwait  
> bootcmd=run mender\_setup  
> bootcount=1  
> bootdelay=2  
> bootdir=/boot  
> bootenvfile=uEnv.txt  
> bootfile=zImage  
> bootm\_size=0x10000000  
> bootscript=echo Running bootscript from ${mender\_uboot\_boot} …; source ${loadaddr}  
> console=ttyO0,115200n8  
> cpu=armv7  
> devtype=mmc  
> dfu\_alt\_info\_emmc=rawemmc raw 0 3751936;boot part 1 1;rootfs part 1 2;MLO fat 1 1;MLO.raw raw 0x100 0x100;u-boot.img.raw raw 0x300 0x1000;u-env.raw raw 0x1300 0x200;spl-os-args.raw raw 0x1500 0x200;spl-1  
> dfu\_alt\_info\_mmc=boot part 0 1;rootfs part 0 2;MLO fat 0 1;MLO.raw raw 0x100 0x100;u-boot.img.raw raw 0x300 0x1000;u-env.raw raw 0x1300 0x200;spl-os-args.raw raw 0x1500 0x200;spl-os-image.raw raw 0x17001  
> dfu\_alt\_info\_qspi=MLO raw 0x0 0x040000;u-boot.img raw 0x040000 0x0100000;u-boot-spl-os raw 0x140000 0x080000;u-boot-env raw 0x1C0000 0x010000;u-boot-env.backup raw 0x1D0000 0x010000;kernel raw 0x1E0000 0  
> dfu\_alt\_info\_ram=kernel ram 0x80200000 0x4000000;fdt ram 0x80f80000 0x80000;ramdisk ram 0x81000000 0x4000000  
> dfu\_bufsiz=0x10000  
> dofastboot=0  
> emmc\_android\_boot=setenv eval\_bootargs setenv bootargs $bootargs; run eval\_bootargs; setenv mmcdev 1; setenv fdt\_part 3; setenv boot\_part 9; if test $reboot\_image = recovery; then setenv boot\_part 8; se;  
> envboot=mmc dev ${mender\_uboot\_dev}; if mmc rescan; then echo SD/MMC found on device ${mender\_uboot\_dev};if run loadbootscript; then run bootscript;else if run loadbootenv; then echo Loaded env from ${b;  
> ethaddr=f8:36:9b:0c:5f:62  
> eval\_bootargs=setenv bootargs androidboot.serialno=${serial#}  
> fastboot.board\_rev=A.2  
> fastboot.cpu=DRA762  
> fastboot.secure=GP  
> fastboot.userdata\_size=unknown  
> fdt\_addr\_r=0x88000000  
> fdt\_part=3  
> fdtaddr=0x88000000  
> fdtcontroladdr=fdefef18  
> fdtfile=dra76-evm.dtb  
> findfdt=if test $board\_name = omap5\_uevm; then setenv fdtfile omap5-uevm.dtb; fi; if test $board\_name = dra7xx; then setenv fdtfile dra7-evm.dtb; fi;if test $board\_name = dra72x-revc; then setenv fdtfil  
> finduuid=part uuid ${mender\_uboot\_root} uuid  
> fit\_bootfile=fitImage.itb  
> fit\_loadaddr=0x88000000  
> importbootenv=echo Importing environment from ${mender\_uboot\_boot} …; env import -t ${loadaddr} ${filesize}  
> kernel\_addr\_r=0x82000000  
> loadaddr=0x82000000  
> loadbootenv=fatload ${mender\_uboot\_boot} ${loadaddr} ${bootenvfile}  
> loadbootscript=load ${mender\_uboot\_boot} ${loadaddr} boot.scr  
> loadfdt=load ${mender\_uboot\_root} ${fdtaddr} ${bootdir}/${fdtfile}  
> loadfit=run args\_fit; bootm ${loadaddr}#${fdtfile};  
> loadimage=load mmc ${mender\_uboot\_root} ${loadaddr} ${bootdir}/${bootfile}  
> machid=fe6  
> mmcboot=if mmc dev ${mender\_uboot\_dev}; then setenv devnum ${mender\_uboot\_dev}; setenv devtype mmc; if mmc rescan; then echo SD/MMC found on device ${mender\_uboot\_dev};if run loadimage; then run loadfdt;  
> mmcdev=1  
> mmcloados=run args\_mmc; if test ${boot\_fdt} = yes || test ${boot\_fdt} = try; then if run loadfdt; then bootz ${loadaddr} - ${fdtaddr}; else if test ${boot\_fdt} = try; then bootz; else echo WARN: Cannot ;  
> mmcrootfstype=ext4 rootwait  
> netargs=setenv bootargs console=${console} ${optargs} root=/dev/nfs nfsroot=${serverip}:${rootpath},${nfsopts} rw ip=dhcp  
> netboot=echo Booting from network …; setenv autoload no; dhcp; run netloadimage; run netloadfdt; run netargs; bootz ${loadaddr} - ${fdtaddr}  
> netloadfdt=tftp ${fdtaddr} ${fdtfile}  
> netloadimage=tftp ${loadaddr} ${bootfile}  
> nfsopts=nolock  
> partitions=uuid\_disk=${uuid\_gpt\_disk};name=rootfs,start=2MiB,size=-,uuid=${uuid\_gpt\_rootfs}  
> partitions\_android=uuid\_disk=${uuid\_gpt\_disk};name=xloader,start=128K,size=256K,uuid=${uuid\_gpt\_xloader};name=bootloader,size=2304K,uuid=${uuid\_gpt\_bootloader};name=environment,size=256K,uuid=${uuid\_gpt}  
> pxefile\_addr\_r=0x80100000  
> ramdisk\_addr\_r=0x88080000  
> rdaddr=0x88080000  
> reboot\_image=boot  
> rootpath=/export/rootfs  
> scriptaddr=0x80000000  
> scsidevs=0  
> serial#=0b0120124c0c0020  
> soc=omap5  
> static\_ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off  
> stderr=serial@4806a000  
> stdin=serial@4806a000  
> stdout=serial@4806a000  
> update\_to\_fit=setenv loadaddr ${fit\_loadaddr}; setenv bootfile ${fit\_bootfile}  
> usbtty=cdc\_acm  
> vendor=ti  
> ver=U-Boot 2016.05-dirty (Aug 02 2022 - 11:03:00 +0530)  
> vram=16M
> 
> Environment size: 7386/131068 bytes

Please let me know if you require any further information.

Thanks  
Nalin